Basic Info
Model NO.: MCSIL-2066/2088 silicone
Material: Silicone Rubber
Form: Liquid Rubber
Color: off-White
Hardness: 28-30 Shore a
Curing Time: 2-3 Hours
Tear Strength: 27 N/Mm
Shrinkage: 0.3%
Specification: REACH, MSDS, SGS
HS Code: 39100000
Raw Material: Silicone Raw Material
Appearance: Liquid
Item: Mcsil-2066
Mixing Ratio: 100:2
Pot Life: 20-30 Mins
Tensile Strength: 3.8 MPa
Enlongation: 420%
Trademark: MC SILICONE
Origin: Dongguan, China
Product Description
Description of Cultured Stone Casting RTV-2 Silicone
RTV-2 silicone is a two-component material, this kind of silicone consists of Part A base silicone and Part B CA30 curing agent, and Part A base silicone and Part B curing agent can cure at room temperature by a condensation reaction. These materials can be cast into the cured silicone molds: Plaster polyurethane, PU, GRC, cement, resin, polyester, wax etc...
Features of Cultured Stone Casting RTV-2 Silicone
1. Good flowability and long working time
2. Medium hardness
3. High tear and tensile strength
4. Easy de-mould from complex replica parts
5. Acid and alkali-resistance
6. Low linear shrinkage
Applications of Cultured Stone Casting RTV-2 Silicone
MCSIL-2066/2088 silicone is especially suited for reproduction of middle size cement molds, concrete stones, and artificial stones. etc...
How to make the silicone mold?
1. Preparing
The surface of the original objects should be clean and free of loose material. If your products have thin flower patterns, and especially have porous substrates, please use a suitable mold release agent such as soap water, detergent, Vaseline or petroleum jelly.
2. Mixing
Please weigh Part A silicone base and part B CA30 Curing Agent with ratio of 100: 2 into a clean container. Stir Part A base silicone thoroughly before use, then Mix Part A and Part B evenly until the curing agent completely dispersed in the silicone base. Manual or mechanical mixture can be used, but do not last much time or allow the temperature to exceed 35C (95F). It's suitable to mix small quantities to ensure thorough mixture of silicone base and curing agent.
Note: It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mixture to completely expand and then collapse. After a further 1 to 2 minutes under vacuum, the mixture should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture. So a suitably large container should be chosen.
3. Pouring the mixture and curing
Pour the mixed Part A base silicone and CA-30 curing agent as soon as possible onto the original object, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 6 hours (or faster by different mixing ratio or room temperature), we advice you de-mold after 24 hours, it is will improve the replicate times of silicone mold.
Packing of Cultured Stone Casting RTV-2 Silicone
Part A base silicone: 20kg/drum, 25kg/drum or 200kg/drum
Part B CA30 Curing Agent: 0.25kg/bottle, 1kg/bottle and 10kg/bottle
Storage of Cultured Stone Casting RTV-2 Silicone
When the RTV-2 silicone is stored at or below 30 C (85F) in the original unopened containers, Silicone Base and CA30 Curing agent have a usable life of 12 months from the date of production.
Note of Cultured Stone Casting RTV-2 Silicone
MCSIL-2066/2088 silicone is an industrial product and must not be used in food molding, dental human skin molding applications.
Need more information, please feel free to contact Nicole.
RTV-2 silicone is a two-component material, this kind of silicone consists of Part A base silicone and Part B CA30 curing agent, and Part A base silicone and Part B curing agent can cure at room temperature by a condensation reaction. These materials can be cast into the cured silicone molds: Plaster polyurethane, PU, GRC, cement, resin, polyester, wax etc...
Features of Cultured Stone Casting RTV-2 Silicone
1. Good flowability and long working time
2. Medium hardness
3. High tear and tensile strength
4. Easy de-mould from complex replica parts
5. Acid and alkali-resistance
6. Low linear shrinkage
Applications of Cultured Stone Casting RTV-2 Silicone
MCSIL-2066/2088 silicone is especially suited for reproduction of middle size cement molds, concrete stones, and artificial stones. etc...
| Item No. | MCSIL-2066 |
| Color | white |
| Mixing ratio | 100:2 |
| Mixed viscosity | 23000-26000 cps |
| Pot life | 20-30 mins |
| Curing time | 2-3 Hours |
| Hardness | 28-30 Shore A |
| Tear Strength | 27 N/mm |
| Tensile Strength | ≥3.8 Mpa |
| Shrinkage | ≤0.3% |
| Elongation at break | 420% |
How to make the silicone mold?
1. Preparing
The surface of the original objects should be clean and free of loose material. If your products have thin flower patterns, and especially have porous substrates, please use a suitable mold release agent such as soap water, detergent, Vaseline or petroleum jelly.
2. Mixing
Please weigh Part A silicone base and part B CA30 Curing Agent with ratio of 100: 2 into a clean container. Stir Part A base silicone thoroughly before use, then Mix Part A and Part B evenly until the curing agent completely dispersed in the silicone base. Manual or mechanical mixture can be used, but do not last much time or allow the temperature to exceed 35C (95F). It's suitable to mix small quantities to ensure thorough mixture of silicone base and curing agent.
Note: It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mixture to completely expand and then collapse. After a further 1 to 2 minutes under vacuum, the mixture should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture. So a suitably large container should be chosen.
3. Pouring the mixture and curing
Pour the mixed Part A base silicone and CA-30 curing agent as soon as possible onto the original object, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 6 hours (or faster by different mixing ratio or room temperature), we advice you de-mold after 24 hours, it is will improve the replicate times of silicone mold.
Packing of Cultured Stone Casting RTV-2 Silicone
Part A base silicone: 20kg/drum, 25kg/drum or 200kg/drum
Part B CA30 Curing Agent: 0.25kg/bottle, 1kg/bottle and 10kg/bottle
Storage of Cultured Stone Casting RTV-2 Silicone
When the RTV-2 silicone is stored at or below 30 C (85F) in the original unopened containers, Silicone Base and CA30 Curing agent have a usable life of 12 months from the date of production.
Note of Cultured Stone Casting RTV-2 Silicone
MCSIL-2066/2088 silicone is an industrial product and must not be used in food molding, dental human skin molding applications.
Need more information, please feel free to contact Nicole.